Car Key Button Repair
A damaged car key is a hassle. It is possible to contact an emergency locksmith service that is available 24 hours a day for help or purchase a new remote.
You could be able to save money by repairing your old key fob rather than replacing it. This is especially true if the issue is caused by an old switch or a damaged contact.
Battery
If the buttons on the key fob aren't responding to pressing the buttons, it could be an obvious indication that your battery is dead or nearing the end of its life. It's simple to replace the battery on your own instead of paying locksmiths or dealers.
First look for the battery compartment. This is usually found on the back of the key fob and could be hidden behind a slide-out cover or an access point that opens when you push a button. Once the compartment has been open then look for the small button-cell battery. This is typically shaped like a coin and identified with a plus and minus sign. Take the battery out and put a brand new one in its place, ensuring that the plus and minus symbols are correctly aligned.
Close the compartment and snap the two halves of your key fob. Before closing the door ensure that you align and snap the pieces into place. To ensure whether sneak a peek here , press any of them.
If your remote key fob ceases working even after you replace the battery, it could be experiencing other issues that require a different kind of repair. Physical damage caused by dropping the fob into a puddle, for instance could cause it to stop working altogether. Alternatively, it might be experiencing an internal electrical problem or might need to be deprogrammed by a dealer or locksmith. Find out if the problem is with your key fob by using these other common methods for troubleshooting your car.
Switches
Based on the year and model, there are a variety of types of switches that are used in the keyfob of your car. The older style keys usually have a separate chip which is visible in the case, whereas modern keys are more sophisticated and operate by sending signals to the car. No matter what type, the buttons on the key can be damaged or worn out with normal use. They become hard to press or not responsive. If you try to press the button too hard the button, it could cause damage and potentially stop the key from being able to start your vehicle in the future.
If you are unable to get your key to function, try changing the batteries. If that doesn't work then you might need to clean your key fob and adjust the switches. These tiny electronic switches are more susceptible than larger components of the key to break because they are constantly tossed about.
The switches are made of rubber, and they're coated with an electrically conducting film that can wear down over time. Fortunately, they're a small part that is easy to replace. The older ones are soldered to the circuit board so you'll need to be careful to remove them without damaging anything else. You can then solder new ones in and reassemble the fob.
An effective way to protect your car key fob from becoming damaged is to not use it for more than a few hours at a stretch, and also to not leave it in areas that it will be visible. Also, make sure you locate a safe place to store your keys when you're not using it.
If the issue continues to persist after you have cleaned your key fob, replaced the battery and tried to clean it, you might need to contact a locksmith. A professional can test the frequency of your key to see if it's still able to communicate with your vehicle, and open and replace micro switches, change cases and much more.
Outer Case
If the buttons aren't able to move freely in the case, they may be stuck or even break. If changing the battery or cleaning with the help of a cotton swab or rubbing alcohol don't resolve the problem, removing the case and examining it could be required. If the contacts that the buttons touch aren't fitting well or are worn out, adjusting them might be the only way to fix the issue.
Rubber buttons may wear out over the years. Rubber buttons can become hard to press because they stretch, and nails may gouge them. In this scenario the key may fail and it's time replace the case or the buttons. This repair involves removing the remote, finding the buttons on the circuit board, heating up the solder before carefully removing them. New buttons are then soldered to the circuit board. The case is then rebuilt with the horse shoe key blade piece attached. The new buttons must be snugly fitted into the case in order to prevent them falling out.
Inner Case
Over time, your key fob's buttons can become damaged or stuck as a result of the constant jolting and accidental pressing. Utilizing metallic tape and a hole punch you can solve this issue in the event your car is not at home and the key fob won't work and allows you to open the doors, but not start the engine. This simple fix can allow you to safely make it back to your vehicle and complete your journey.